Keep it crisp

Maintenance & tuning

A practical owner's guide to keeping a 35-plus-year-old two-stroke healthy, built around Honda's factory baselines.

Last reviewed

Use the manual. This page explains what to do and why. For torque values, clearances and service limits, use the Honda factory service manual (61HB903) or the Clymer TRX250R manual. Don't guess at torque on a two-stroke top end.

Before every ride

  • Tire pressures set, with no cuts or bulges. Check wheel nuts.
  • Throttle snaps closed with the bars turned fully left and right.
  • Front and rear brakes are firm. Check fluid levels and look for leaks.
  • Chain tension and lubrication. Make sure the axle and sprocket nuts are tight.
  • Coolant level, and no leaks at hoses or the water pump.
  • Air filter is clean and oiled, and the airbox is sealed.
  • Fuel is freshly mixed at the right ratio.
  • Kill switch works.

Premix: oil ratio & fuel

The 250R has no oil injection, so it lubricates its crank and top end only from oil mixed into the fuel. Honda's factory specification is 20:1, set for the two-stroke oils of the 1980s. Modern two-stroke oils are much better, and many owners run leaner ratios. Use the ratio your oil maker recommends for high-performance or racing use, and re-check your jetting whenever you change ratio or oil brand, because more or less oil changes the air/fuel mixture.

  • Mix in a clean, dedicated can, and add the oil before the last of the fuel so it mixes thoroughly.
  • Use fresh, good-quality fuel. Ethanol-blended pump gas absorbs water and goes stale faster. Mix only what you'll use within a few weeks, and drain the carburetor before storage.
  • Never use oil meant for oil-injected engines or four-strokes.

Premix calculator →

Jetting basics

The stock carburetor is a 34 mm Keihin PJ flat-slide. Factory baselines:

Setting1987 (PJ07A)1988 (PJ07B)
Main jet#152#158
Pilot jet#48#45
Needle clip3rd groove3rd groove
Air screw1⅞ turns out1¾ turns out
Float level16 mm16 mm

Tune in throttle-position order. Each circuit overlaps the next, so work through them in sequence:

  1. Idle to ⅛ throttle: pilot jet and air screw. On the PJ the air screw sits on the air-filter side and meters air, so turning it out leans the mixture and turning it in richens it. If the best idle comes with the screw less than about 1 turn out, the pilot jet is too small, so go one size bigger. If it's beyond about 2½ turns out, the pilot is too big, so go one size smaller. If the screw changes nothing, clean the pilot circuit.
  2. ⅛ to ¼ throttle: slide cutaway (rarely changed).
  3. ¼ to ¾ throttle: needle clip position. Raising the clip (moving it to a higher groove) lowers the needle and leans the mixture. Lowering the clip richens it.
  4. ¾ to full throttle: main jet. Do a plug chop: run at full throttle in a high gear, hit the kill switch and pull in the clutch at the same moment, then read the plug.

Lean seizes, rich fouls. A lean two-stroke can seize a piston in seconds. When in doubt, err slightly rich and work leaner one step at a time. Cold, dense air needs more fuel (bigger jets). Heat and altitude need less.

Spark plug

Factory plug: NGK BR9ES, gapped at 0.7–0.8 mm (0.028–0.031 in). The "R" means it has a resistor. Some trail riders run the one-step-hotter BR8ES to resist fouling at low speeds. Racers often stay with the 9 heat range. When reading a plug, look at the ring of color deep on the insulator, not the tip. A tan to light-brown ring means you're in the right range. Chalky white means lean, and wet black means rich.

Gearbox oil

The transmission and clutch run in their own oil bath, separate from the premix. Capacity is 0.6 L (0.63 US qt) at an oil change and 0.7 L after disassembly. Use the transmission oil grade listed in your manual or a quality motorcycle gear or clutch oil made for wet clutches. Change it often: it's cheap and the clutch wears it out quickly. Milky oil means water or coolant is getting in, so check the water-pump seal.

Air filter

The stock filter is oiled polyurethane foam. Wash it in a dedicated filter cleaner, let it dry fully, oil it evenly with foam-filter oil, and grease the sealing rim. Dust that gets past the filter wears out a two-stroke top end very quickly. Check the airbox boot and carb clamp every time you service the filter.

Cooling system

Use antifreeze made for aluminum engines, mixed as the manufacturer directs (or a premixed product). Check the radiator fins, cap seal, hoses and clamps. Flush the system and replace the coolant on a regular schedule. Overheating on a two-stroke is a fast way to a seized piston.

Chain & sprockets

Stock final drive is a 520 O-ring chain, with 13/39 sprockets on 1986–87 and 13/38 on 1988–89. Keep it lubricated with an O-ring-safe chain lube, and set slack to the figure in your manual, measured with the suspension at the position the manual specifies. Replace the chain and both sprockets together once the teeth are hooked or the chain has stretched.

Top end, reeds & exhaust

  • Top end: how often to replace the piston and rings depends entirely on how you ride. Racers do it on a schedule measured in hours, while trail riders go much longer. Measure piston-to-cylinder clearance and ring end gap against the manual's service limits, and replace parts before they hit the limit. Many 250Rs have been bored oversize or re-plated, so always confirm what's in there before you order a piston.
  • Reeds: chipped or warped petals cost power and make the engine hard to start. Inspect them whenever the intake is off.
  • Exhaust: repack the silencer periodically, and check the expansion chamber for dents and cracks. Dents change how the pipe performs.
  • Crank seals: on an engine this old, the seals have often hardened. A high or hanging idle you can't fix with jetting is the classic symptom. Pressure/vacuum test before you assume it's jetting.

Storage

  • Drain the carb float bowl. Old premix varnishes the jets quickly.
  • Fog the cylinder, or at least kick it over until it's on compression, to close the ports.
  • Change the gearbox oil before storage, not after.
  • Keep the tires off bare concrete if you can, and plug the exhaust and airbox against mice.