Reference
TRX250R specifications
Factory specifications for the 1986–1989 Honda TRX250R, split by generation where they differ. Every figure is cross-checked, and where published sources disagree, we say so.
Last reviewed
Two generations. The 1986–87 models share the first-generation chassis (steel swingarm, bar-mounted headlight). The 1988–89 models use the redesigned chassis (aluminum swingarm, headlight in the front fender). Engines changed in 1987 (long rod) and again in 1988 (revised cylinder and intake). Not sure which one you have? Identify your year.
Engine
| Type | Liquid-cooled, two-stroke, single cylinder, reed-valve induction, counterbalanced |
|---|---|
| Displacement | 246 cc (15.0 cu in) |
| Bore × stroke | 66.0 × 72.0 mm (2.60 × 2.83 in) |
| Cylinder | Iron liner; inclined 7° forward |
| Compression ratio | 7.5 : 1 (1986) · 7.7 : 1 (1987–89) |
| Connecting rod | 1987–89 rod is 5 mm longer than 1986, with the piston's wrist-pin bore raised 5 mm to match |
| Power valve | None (all years) |
| Lubrication | Fuel/oil premix, 20 : 1 factory specification |
| Starting | Kick start |
| Ignition | CDI (capacitor discharge), electronic advance |
| Initial ignition timing | 19° BTDC (1987) · 21° BTDC (1988), per factory data |
| Spark plug | NGK BR9ES, gap 0.7–0.8 mm (0.028–0.031 in) |
| Engine dry weight | 26 kg (57.3 lb) |
| Rated horsepower | Honda did not publish a widely cited official figure. Treat any single "stock hp" number online with caution. |
Carburetor & factory jetting
| Item | 1986 | 1987 | 1988–89 |
|---|---|---|---|
| Carburetor | Keihin PJ, 34 mm piston-valve (flat-slide) | ||
| Carb ID mark | PJ05A | PJ07A | PJ07B |
| Main jet | — | #152 | #158 |
| Pilot (slow) jet | — | #48 | #45 |
| Needle clip | — | 3rd groove | 3rd groove |
| Pilot (air) screw | — | 1⅞ turns out | 1¾ turns out |
| Float level | — | 16 mm (0.63 in) | 16 mm (0.63 in) |
| Air filter | Oiled polyurethane foam | ||
"—" = no verified factory figure found. Factory jetting is a sea-level baseline for a stock engine with stock pipe and airbox. Altitude, temperature, oil ratio and modifications all change it. See jetting basics.
Transmission & gearing
| Clutch | Wet, multi-plate, manual (left-hand cable lever) |
|---|---|
| Transmission | 6-speed, constant mesh, close ratio; no reverse |
| Shift pattern | 1-N-2-3-4-5-6 (left foot; one down, five up) |
| Primary reduction | 2.652 |
| Final drive | 520 O-ring chain. 1986–87: 13/39 (3.000) · 1988–89: 13/38 (2.923) |
| Gear | Ratio | Overall, 1986–87 (13/39) | Overall, 1988–89 (13/38) |
|---|---|---|---|
| 1st | 2.570 | 20.45 : 1 | 19.92 : 1 |
| 2nd | 2.062 | 16.41 : 1 | 15.98 : 1 |
| 3rd | 1.667 | 13.26 : 1 | 12.92 : 1 |
| 4th | 1.333 | 10.61 : 1 | 10.33 : 1 |
| 5th | 1.087 | 8.65 : 1 | 8.43 : 1 |
| 6th | 0.920 | 7.32 : 1 | 7.13 : 1 |
Overall = primary × gear × final. Try your own sprocket combinations in the gearing calculator.
Chassis, suspension & brakes
| Item | 1986–87 | 1988–89 |
|---|---|---|
| Frame | Steel square-tube | Redesigned steel square-tube |
| Swingarm | Steel, gold finish; rear engine mount shares the swingarm pivot bolt | Aluminum, about 1 in shorter; separate frame-mounted rear engine mount |
| Front suspension | Dual A-arms, twin Showa shocks with 5-position spring preload; 200 mm (7.9 in) travel | |
| Rear suspension | Pro-Link single Showa shock, adjustable spring preload, compression and rebound damping; 230 mm (9.1 in) travel | |
| Caster / trail | 6° / 27 mm (1.06 in) | 4°40′ / 21 mm (0.83 in) |
| Brakes | Hydraulic disc: twin front discs, single rear disc on the axle | |
| Front tires | 21×7-10 | 22×7-10 |
| Rear tires | 20×10-9 | |
| Rims | Front 10×5.5 · Rear 9×8 | |
| Original tires | Ohtsu. Radial Ohtsu tires appear on later-model spec sheets (notably 1988). | |
| Headlight | Handlebar-mounted, 60/55 W halogen | Front-fender (nose) mounted, 60/55 W halogen |
Dimensions, weight & capacities
| Item | 1986–87 | 1988–89 |
|---|---|---|
| Overall length | 1,825 mm (71.9 in) | 1,840 mm (72.4 in) |
| Overall width | 1,130 mm (44.5 in) | 1,160 mm (45.7 in) |
| Overall height | 1,070 mm (42.1 in) | 1,080 mm (42.5 in) |
| Seat height | 775 mm (30.5 in) | 790 mm (31.1 in) |
| Wheelbase | 1,295 mm (51.0 in) | 1,265 mm (49.8 in) |
| Ground clearance | 110 mm (4.3 in) | |
| Dry weight | Published claims range from about 330 to 357 lb, depending on year and source. The 1988 redesign is credited with saving roughly 25 lb. | |
| Fuel tank | 10.0 L (2.6 US gal), including 2.0 L (0.5 US gal) reserve | |
| Transmission oil | 0.7 L (0.74 US qt) at disassembly · 0.6 L (0.63 US qt) at oil change | |
| Top speed (claimed) | About 71 mph (stock gearing) | |
| Original MSRP | $2,498 (1986) | |
Model codes & publications
| VIN / frame prefix | JH3TE12…. The 10th character gives the year: G 1986, H 1987, J 1988, K 1989 |
|---|---|
| Honda model code | TE12 (frame) · HB9 (product code) |
| Factory service manual | Honda 61HB903 |
| Aftermarket manual | Clymer, Honda TRX250R/FourTrax 250R & ATC250R 1985–1989 (ISBN 0-89287-540-2) |
About these numbers. Factory figures come from Honda specification data and the service-manual tables cited on our sources page. Published sources disagree in a few places. We list the 1986–87 wheelbase from factory data (1,295 mm); some references print 51.2 in for 1986. Dry weights vary from source to source, so we give the range. One widely shared table says the wheelbase grew for 1988. Factory dimensions show it shrank from 1,295 to 1,265 mm, which is consistent with the shorter swingarm. Always torque, gap and jet from the factory service manual for your exact model year.
Want this data in machine-readable form? It's available as JSON.